Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You may locate that your garage door opener has been giving you troubles, so you need to fix it. You can repair it by changing a circuit board, a photo-eye sensor, the main drive equipment, or the set-limit buttons. You can also inspect if the safety and security sensors are working properly.

Replacing a motherboard

Replacing a circuit board for your garage door opener requires a few actions and devices. Initially, you need to shut off the circuit breaker as well as disconnect any kind of cords. Next off, open the circuit card cover. This will certainly assist you to detect the problem and establish if you need a brand-new board. Next, remove the old board and also its cord ports.

You can then proceed to change the motherboard. The replacement procedure is easy and also takes around 10 minutes. A brand-new circuit board will set you back about $80. To safeguard your new motherboard from power rises, you can purchase a rise protector.

Replacing a photo-eye sensing unit

Changing a photo-eye sensing unit can be a relatively straightforward job. Initially, eliminate the sensor from the door and make certain it is located correctly. If the sensing unit is angled in any way, it may not be getting the appropriate signal, which can be creating the blinking lights. If you see that the photo-eyes are out of placement, you might require to have actually a service technician come and also deal with the issue.

The photo-eye sensing unit consists of 2 items that place on the outside of the door tracks and also toward the floor. The photo eyes will certainly have a small LED light and also should be solid in shade. If the light is blinking, its most likely the photo-eye is defective and also will need to be changed.

Replacing a primary drive equipment

To change a garage door opener main drive gear, begin by eliminating the cap from the chain wheel. Next, remove the two screws holding the drive gear to the gear setting up. Now, you can loosen the 3 tension pins. Press them from both sides and then eliminate them. After that, disconnect the three cords from the garage door opener motor. These cables need to be white, red, as well as blue.

When you have actually eliminated the old equipment, set up a brand-new one. Make certain to oil it well. Place the brand-new gear into the shaft, making certain to align the placing openings. Make sure the gear and sprocket setting up are located properly to ensure smooth procedure. Next off, utilize a hammer as well as a nail to drive a pin right into the brand-new gear.

Adjusting the set-limit switches

The very first point you ought to do if your garage door is not working appropriately is to examine the set-limit buttons. You may require to change them so that the door closes earlier or stops prior to it gets to the flooring. You can inspect this by considering your garage doors manual or online.

To change the set-limit buttons, youll require a screwdriver or socket. Change the knob clockwise or counterclockwise up until the door moves up and also quits, or minimizes its distance. To look for appropriate traveling distance, measure the void from the bottom of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Key St Ste 105, Keller, TX 76248, United States

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *


Back To Top